We already liked the Lelit Elizabeth in its first test. Now Lelit has followed up: The Elizabeth 3 is a dual boiler for €1,650 that controls pressure and flow in two ways. With the Pagaia, the small wooden lever on the side, you can regulate the flow during extraction by hand. Additionally, you can save a pressure profile with up to five steps on two buttons. This makes extractions repeatable, and that wasn't available at this price point before.
We measured the Elizabeth 3 according to our test protocol 2.3.2 and ran the old Elizabeth through the same protocol again in parallel. This way you can compare both machines directly. The key question: What does the new control deliver in the cup, and what does the smaller brew boiler cost?
We didn't buy this machine. We received it before the official market launch so we could test it in time, and at that point Lelit couldn't send us an invoice. This doesn't change our testing procedure—we test as always, independently and carefully.
Because we want to maintain our neutrality by paying for each test device, we're donating the purchase price of €1,650 to the Instituto "Fazenda da Cachoeira" in Brazil. It carries out cultural and educational work in the field of regenerative agriculture, conducts knowledge transfer in collaboration with universities, and runs projects on integration and empowerment.
We've already tested the old Elizabeth extensively. You can find the test of the Lelit Elizabeth with the new measurements here, and we explain how the lever works on the Victoria and Mara in our article about Lelit Pagaia.
What's new: Pressure profiles, Pagaia, and a smaller brew boiler
At first glance, the Elizabeth 3 looks the same as before. It still weighs 15 kilos and at 38 centimeters wide, 38 centimeters tall, and 36 centimeters deep it's almost a cube. Inside, though, some things have changed. The brew boiler has shrunk to 0.2 liters, the steam boiler stays at 0.6 liters, and the water tank holds 2.5 liters.
The real innovation is the pump control. Lelit regulates the vibratory pump via pulse width modulation, controlling how much power goes to the pump. A pressure sensor simultaneously measures how much resistance the coffee puck exerts on the pump. The technology is based on Sage patents, the company group that Lelit now belongs to. The result is what you see on the display: During extraction, the machine shows the pressure on the coffee and the set profile.

Buy Lelit Elizabeth 3
The following specialty retailers stock the Lelit Elizabeth 3 and we can recommend purchasing from these businesses.
Switzerland: [Partner links] Simons Kaffee
* We search for specialty partners for you whom we know do good work and offer good service. We stay in close contact with the retailers. These are commission links. If you order through this link, it costs you no more, but we receive a small commission that we put toward new test equipment.
Build quality: Wood instead of plastic, and very quiet at 56 decibels
In the first test with the old Elizabeth, we criticized the steam knob as cheap and unaesthetic, and many of you then built your own knobs from wood or 3D printers. That's done now. Steam knob, portafilter handle, tamper, and Pagaia are all from the same wood, and everything feels significantly more premium. The water tank cap now also sits in a small guide. As usual, Lelit uses rubber buffers, so there's less rattling.
You notice this during brewing too. At 56 decibels, the Elizabeth 3 is very quiet, and especially with a pressure profile, the pump purrs rather than rumbles. In our rating, that's an 8.
It's not entirely without drawbacks. The stainless steel sheet is relatively thin and has a somewhat sharp edge in one spot, and you can see every fingerprint on the brushed stainless steel. Michel would therefore go for the black version because the finish looks more premium and shows fewer marks. Black and white cost €50 more. Overall, we rate the build quality at 8.
Pressure profiles: five steps per button
Each of the two extraction buttons can store its own profile with up to five steps. For each step, you set the pressure in half-bar increments and the duration. You don't need a complicated app for this—programming is done via the familiar Lelit display.
You don't have to use all five steps. If you set the second step to 30 seconds, steps three through five won't come into play because no extraction lasts that long. For everyday use, often just a gentle wetting of the coffee puck followed by brewing at 8.5, 9, or 7.5 bar is enough. If you like, you can store a manual lever profile with all five steps that climbs to 9 bar and then drops a bar every few seconds.
The display is the same one Lelit has been using for years. It takes a bit of finesse, but once you know the logic, you'll find your way around quickly. Michel found saving the profiles intuitive. Beyond that, there are settings for steam temperature, the steam boiler can be turned off, and the lighting can be adjusted.

Pagaia: regulate the flow during extraction by hand
Do you need the lever at all if the machine stores profiles? Yes and no. With the Pagaia, you start the extraction right on the side and then respond to what you see and what the display shows for pressure. It's practical if you want to try a recipe from your roaster without immediately saving it, or if you just want to control it freely and by hand.
The lever is even more useful when a shot goes off the rails. In our test, one extraction ran too fast toward the end, even though we'd already set the grind finer. With the Pagaia, we slowed the flow and landed at 22 to 23 seconds. At 9 bar, the coffee probably would have gone through in 19 seconds. More expensive machines with flow control like the Maro do this automatically and call it Smart Profiling. Here you do it yourself. There's one limitation: You have to start the extraction on the lever. If you start via the button, you can't switch to the lever mid-extraction.
Whether you really need both features was something the team wasn't entirely agreed on. For one of us, electronic control alone would have been enough if the machine were €200 cheaper. The other appreciates the lever precisely as a tool to rescue individual shots. However, the lever can't be combined with an electronically stored profile.
Espresso: Robusta with profile, 18.5 grams in the basket
For the first espresso, Michel deliberately chose something unexpected: a pure, washed Robusta from India called Bharath. 18.5 grams in the double basket. He brewed it with a profile: eight seconds at 3 bar to fully wet the coffee puck, then 8.5 bar for the remaining 17 seconds, yielding 45 grams in the cup.
In the cup it's very full-bodied, with a peaty, dark note reminiscent of black bread. The baskets are the usual stamped ones, solid but not a highlight. If you want to upgrade, go for a cylindrical basket that goes straight down, like our KM Professional Baskets.

Brewed in test: Bharath, espresso from India
Washed Robusta from Bharath Belliappa, with warm cocoa, marble cake, and creamy texture.
Technically, the Elizabeth 3 has a lot of potential. We rate the pressure control at 2.5 out of 3.5 points, the hardware at 1.5 out of 2. With it, you can brew a strong Robusta just as well as a very light roasted competition coffee. Temperature is a limiting factor, which we'll cover shortly. All in all, the espresso potential stands at 6.5 across all extractions. If you know how to work with the Elizabeth 3, you'll get everything out of each individual extraction anyway. For that, you should know how the temperature behaves on the second and third extraction.
We explain how to basically set grind and brew ratio in our guide to making espresso.
Temperature: 93.6 °C on the first extraction, then 2 degrees less
With temperature, the Elizabeth 3 has taken a step backward compared to its predecessor, probably also because of the smaller brew boiler. You can brew very precisely with it. It becomes problematic only when you make many extractions in a row and don't know how the machine behaves. That's why we spent a lot of time with the new Elizabeth to thoroughly investigate its behavior for you.
We measure with the Scace directly in the portafilter, each time at a set 94 °C. In the KM protocol, we pull five double espressos at one-minute intervals. The first extraction after 20 minutes is at 93.6 °C, so only 0.4 degrees below the setting. From the third extraction onward, the Elizabeth 3 settles at 91.6 to 91.8 °C and doesn't drop further.
Our rating is based on the protocol with one-minute intervals. If you give the machine two minutes between extractions, it becomes much more consistent: All five espressos then fall within 0.9 degrees, between 91.4 and 92.3 °C. That's easily manageable at home. Serve the espresso, prepare the next one, and with single dosing, two minutes are over quickly.
With one or two espressos, you're in a good range anyway. When guests come and you're pulling more extractions in a row, give the machine two minutes between shots. Then the temperature stays stable from cup to cup.
| KM Protocol | Extraction 1 | Extraction 2 | Extraction 3 | Extraction 4 | Extraction 5 | Range |
|---|---|---|---|---|---|---|
| Elizabeth old, 20 min., 1 min. break | 84.82 | 84.40 | 87.26 | 89.79 | 93.42 | 9.02 |
| Elizabeth old, 25 min., 1 min. break | 90.71 | 92.52 | 93.60 | 94.01 | 93.64 | 3.30 |
| Elizabeth 3, 20 min., 1 min. break | 93.60 | 92.38 | 91.79 | 91.64 | 91.75 | 1.96 |
| Elizabeth 3, 20 min., 2 min. break | 92.27 | 92.10 | 92.10 | 91.44 | 91.35 | 0.92 |
All values in °C, average per extraction across seconds 5 to 25, set to 94 °C. The row with two-minute breaks deviates from the standard protocol and shows our recommendation for everyday use.
The step backward is clearer in the WBC protocol, that is, 14 extractions at short intervals with parallel milk steaming. The Elizabeth 3 starts at just under 95 °C and ends just under 90 °C. The temperature window is 5.5 degrees. The old Elizabeth holds the first eleven extractions in this test between 92.8 and 94.6 °C and only drops at the end. For catering with many extractions in a row, the Elizabeth 3 is therefore not built.
In the temperature rating, the first extraction, which hits almost exactly, gets the full points. We deduct for the drop across five extractions, for the slightly rising curve within the shot, and for the WBC test. All together, that's a 5.9.
Preheat time: 20 minutes until stable temperature
The Elizabeth 3 is somewhat faster than its predecessor, but not really quick. We estimate 25 minutes for the old Elizabeth based on the retest, 20 minutes for the new one. Only then do the extractions deliver the temperature we described above. We also measured after 15 minutes: The five extractions at a set 93 °C were only between 88.4 and 89.2 °C. That's consistent, but roughly four degrees too cold.
Other reviews mention nine minutes, and that's what Lelit states too. Lance Hedrick tested that in his video and got 89.6 °C at a set 90 °C. We don't want to dispute that. The machine heats at full power for the first good eight minutes, and a single shot can certainly work after that. Our protocol asks about a series of extractions, and that's definitely too cool after 15 minutes.
We ran a measurement series at a set 93 °C after 15 minutes, and the temperature averaged 88.66 °C. If Lance had set his machine to more than 90 °C, he probably would have seen that it doesn't reach temperature after 10 or even 15 minutes.
The Elizabeth 3 needs 20 minutes to be properly warmed up for multiple extractions in a row. By the way, our power measurement also explains quite well why the machine reaches 88 to 90 °C quickly but then doesn't quickly reach 93 °C: After about eight minutes, it stops heating at full power. Lelit left some preheat speed on the table there.
Anyone looking for a machine that's ready after just a few minutes won't find it in the Elizabeth 3. Thin-film heaters and thermoblocks are much faster. The Elizabeth 3 therefore gets a 4 for preheat time. Once it's up to temperature, though, the temperature stays reasonably stable, especially if you follow our temperature tip.
Steaming: 300 ml in 30 seconds to 60 °C
Surprisingly a lot has changed with steaming, even though the steam boiler stayed the same size. The Elizabeth 3 steams faster and with more pressure than the old one. It brings 300 milliliters of milk from 8 to 60 °C in 30 seconds. That's brisk, but not so fast it becomes difficult. You just need to tilt the pitcher slightly to get a nice rotation. About 4 milliliters of condensation come out of the wand before steaming; it's insulated and doesn't feel that hot.
It's not a catering machine here either. After the third or fourth steaming in a row, the power drops noticeably. We don't rate that negatively because the machine is intended for home use. The steaming quality gets a 7.8. You can find the matching milk pitcher for latte art in our shop.
Volumetrics: Time-based control instead of flow meter
The two buttons work with time-based control, not a flow meter. You can debate whether a flow meter wouldn't have been nice. But a flow meter that also delivers precisely with changing pressure profiles doesn't exist for €1,650—that quickly costs significantly more. Even pricier machines that claim to do it often fail at that.
If you work consistently and have set up the machine once properly, the time-based control delivers the water solidly. That's not volumetrics in the strict sense, though. Our recommendation: Measure with an espresso scale. For pure time-based control, the rating is a 3.
Power consumption: 0.075 kWh in espresso mode
We explain how we measure in our power measurement. For the rating on dual boilers, the economical espresso mode counts—that is, preheat and one espresso with the steam boiler off. The Elizabeth 3 comes in at 0.075 kWh, and that's a very good value for a dual boiler. With the steam boiler on, it's 0.154 kWh for one espresso and 0.172 kWh for a cappuccino, so roughly double.
The curve shows where the electricity goes. With the steam boiler, the machine heats at full power of about 990 watts for the first good eight minutes, consuming 0.126 kWh in the process. After that, the PID only maintains temperature with brief pulses, and the remaining twelve minutes until the first extraction cost 0.019 kWh. Without the steam boiler, the full-power phase is over after 2 minutes and 20 seconds, and after 20 minutes, the meter reads 0.068 kWh—less than half.
Because both boilers are small, power retention stays manageable for a dual boiler, even though preheat time is long. The second ten minutes of preheat time needed for stable temperatures costs just 0.016 kWh with the steam boiler. During brewing, the heater kicks in briefly after each extraction; one espresso costs 0.007 kWh without and 0.009 kWh with the steam boiler. If you have coffee early, midday, and evening, you're better off switching the machine on 20 minutes before each time rather than keeping it warm all day. Keeping it warm costs 0.084 kWh per hour with the steam boiler, 0.045 kWh without. That's an 8 in the rating.
If you only drink espresso, turn off the steam boiler. Preheating and the first espresso then use only half the electricity. A note from our measurements: In our temperature run without the steam boiler, the extractions at a set 94 °C were around 90 °C, so about 2 degrees lower than with the steam boiler on.
Accessories and operation
The tamper was always good at Lelit, and that remains the case. At 58.55 millimeters, it sits flush with the basket, with no noticeable gap. You also get a cleaning kit, a blind basket, baskets in various sizes, and optional taller rubber feet. As usual with Lelit, only one portafilter with double spout comes with it. The spouts are close enough together that they fit in most espresso cups. We really like this Lelit portafilter, by the way, because the espresso flows out so nicely, like a hazelnut-creamy stream into the cup, almost as pretty as with a bottomless portafilter. We rate the accessories at 8.
As always, a water filter is included. It removes the total hardness but leaves the alkalinity, which somewhat neutralizes the taste. We don't recommend this type of filtration for coffee. You're still protected from limescale, though.
In daily use, the drip tray with 1,200 milliliters helps, and the water tank is easy to remove. Unfortunately, the water level is hard to see. The operating manual explains the programming solidly and effectively, but doesn't go deep. We received one of the first units with English instructions. Lelit is generally not very transparent in its manuals, even though the machines often have more settings than described. We rate usability at 7.

Elizabeth 3 or old Elizabeth?
The new Elizabeth is a different machine. It reaches stable temperature faster, steams more powerfully, is quieter, and can store pressure profiles. In exchange, it loses more temperature than the old model when pulling many extractions in a row. If you mainly drink one or two espressos a day and want to experiment with profiles, the Elizabeth 3 is better for you. If you regularly pull many espressos in succession, check out our dual boiler tests with larger brew chambers.
KM Rating
0 – 100
At 61.7 out of 100 points, the Elizabeth 3 falls into the "Good / Standard" category. That sounds more subdued than we felt about the machine during testing, and there's a reason: Our protocol evaluates the entire package. Weak individual scores in volumetrics, preheat time, and catering potential pull the average down, while the pressure profiles only factor partially into espresso potential. That's why the calculated value-for-money rating of 5.1 is just above market average.
Conclusion: Pressure profiles for €1,650
Would we recommend the Elizabeth 3 to a good friend investing €1,650 in an espresso machine? Michel's answer came without hesitation: "For God's sake, yes!" That's still a lot of money. But a dual boiler with electronically controlled, storable pressure profiles hasn't existed at this price point before. Previously, the only way was if you built flow control onto a machine yourself, or you went to significantly pricier machines like the Sanremo You.
The weaknesses are clear. 20 minutes preheat time, time-based control instead of true volumetrics, and a small brew boiler that loses temperature with many extractions in a row. Add to that the thin sheet metal, where every fingerprint is visible. If you give the machine two minutes between shots at home, you'll get stable temperatures with a deviation from the setting that's unusually small for Lelit.
The Elizabeth 3 makes good espresso, steams decently, and lets you experiment with pressure profiles if you want. But you can just as easily brew at 9 bar, and the coffee tastes great that way too. We've summarized which architecture generally suits you best in our espresso machine buying guide.
No time for the whole video? We've condensed the key findings into ten minutes:
Technical specifications at a glance
| Feature | Lelit Elizabeth 3 |
|---|---|
| Price | approx. €1,650 (stainless steel), approx. €1,700 (black, white), recommended retail price Germany, as of October 2026 |
| Type | Dual boiler with PID |
| Boiler | Brew boiler 0.2 l, steam boiler 0.6 l |
| Pump | Vibratory pump with pulse width modulation and pressure sensor |
| Profiling | 2 buttons with 5 pressure steps each, Pagaia lever for manual flow control |
| Volumetrics | Time-based control |
| Preheat time | 20 minutes (measured) |
| Brew temperature | 93.6 °C on first extraction, 91.6–91.8 °C from extraction 3 onward (set to 94 °C) |
| Power consumption | 0.075 kWh preheat + espresso without steam, 0.154 kWh with steam; standby 0.045 / 0.084 kWh per hour |
| Noise level | 56 dB |
| Water tank | 2.5 l |
| Drip tray | 1.2 l |
| Dimensions (W × H × D) | 38 × 38 × 36 cm |
| Weight | 15 kg |
| Portafilter / Tamper | 58 mm / 58.55 mm |
We didn't buy this machine ourselves because it wasn't available before the market launch. We're donating the purchase price to a social organization in Brazil. We discussed getting the Elizabeth 3 early with Lelit at the trade show booth in Brussels.
























